HCEM HC580D twin-head oil-free piston vacuum pump shown with a separate electronics module

How to Control Vacuum Pressure: Regulators, Bleed Valves, Controllers and Pump Speed

HCEM Engineering Team

To control vacuum pressure you either change how much gas the pump removes (throttle the line to the pump, switch it on and off, or change its speed) or change how much gas comes in (open a bleed or a vacuum breaker). A vacuum regulator does the first automatically with a spring-loaded diaphragm; a vacuum breaker does the second. A vacuum controller adds a sensor and switches a valve or the pump between two set points, or holds one set point with a proportional valve or a speed-controlled pump. Which one is right depends on how tightly the pressure must be held, whether several users share one pump, and how much air you can afford to let in. Whatever you choose, no control method can make the vacuum deeper than the pump can pull at that flow, so the pump is sized for the controlled pressure, not for its rating.

This guide is for engineers who build vacuum into equipment and for anyone who has to hold a process at a set vacuum: lab filtration and drying, holding and handling, degassing, packaging. It explains what "control" and "regulation" mean in a vacuum system, compares the methods side by side, shows how a mechanical vacuum regulator and a vacuum breaker work, works through the numbers for a bleed valve and for two-point control, and ends with what all this means for choosing the pump. Pressures are given as gauge kPa with absolute mbar alongside; for the difference see what is gauge pressure.

What does "controlling vacuum pressure" mean?

Leybold's vacuum fundamentals page on pressure control (read 2026-11-20) separates two ideas that are often mixed up:

  • Control is open loop. Something acts on the system without checking the result, for example a valve opened by a pressure switch. If something else changes, the pressure drifts and nothing corrects it.
  • Regulation is closed loop. The actual pressure is compared with a setpoint all the time, and the difference is corrected. Leybold notes that regulation always includes control; the difference is the controller that compares setpoint and actual value.

Leybold also separates two styles of regulation. Discontinuous (two-step or three-step) regulation keeps the pressure inside a window: it may wander between a lower and an upper switching point. Continuous regulation, for example PID, holds one setpoint as closely as possible. Leybold's view is that continuous regulation is the more elegant one, but that two-step or three-step regulation is often fully adequate.

And there are only two levers. In Leybold's words, the pressure in a vacuum system can be adjusted by changing the pumping speed (changing the pump's speed, or throttling with a valve) or by admitting gas (opening a valve). Every device in this article pulls one of those two levers, or both.

The units you will set it in

Regulators and controllers are sold with gauge scales (kPa, inHg of vacuum), absolute scales (mbar, Torr) or both. The table converts common setpoints at a standard atmosphere of 101.325 kPa, using the NIST conversion factors (1 inHg = 3.386389 kPa, 1 Torr = 133.3224 Pa). At altitude or in bad weather the gauge reading for the same absolute pressure changes; for an absolute process, set and measure in absolute units.

Gauge Vacuum (inHg) Absolute (mbar) Absolute (Torr)
−20 kPa 5.9 813 610
−50 kPa 14.8 513 385
−70 kPa 20.7 313 235
−80 kPa 23.6 213 160
−92 kPa 27.2 93 70
−98 kPa 28.9 33 25

For more unit conversions see bar vs psi, and for flow units our CFM to L/min converter.

The ways to control vacuum pressure, compared

Putting Leybold's two levers together with the device types described by Equilibar, VACUUBRAND, Kurt J. Lesker and SMC (all read 2026-11-20) gives five practical methods for rough vacuum. The table sums up what each source says; the sections below explain each one.

Method Lever How tightly it holds Good for Watch out for
Bleed valve (hand-set needle or "false air" valve) Admits gas Rough and indirect (VACUUBRAND) Simple jobs such as filtration Lets air (oxygen) in; disturbs other users on a shared line; the pump runs flat out all the time
Vacuum breaker / vacuum relief regulator Admits gas, automatically Holds a setpoint, but usually not precisely over a wide flow range (Equilibar) Protecting some pumps from going beyond their design vacuum; often smaller and cheaper Extra gas flow wastes energy with some pumps; disturbs other processes on a shared header
Vacuum regulator (throttling, back-pressure type) Throttles the flow to the pump Can be very precise, depending on design and sizing (Equilibar) Several processes on one vacuum supply; keeping gas flow low Must be sized to pass the whole vacuum flow; a non-relieving type cannot raise the pressure without some inflow
Vacuum controller with an on/off valve (two-point) Throttles (open/closed) Swings between two switching points (hysteresis) Holding a level within a window, automatically Pressure ripple; frequent valve or pump switching
Speed-controlled pump with a controller Changes pumping speed Continuous, close to the setpoint (VACUUBRAND) Processes whose demand changes; energy and noise Needs a pump and drive built for variable speed

For high vacuum processes, Kurt J. Lesker describes two more: upstream control, metering process gas in with a mass flow controller, and downstream control, a motorized throttle valve in front of a turbo pump, or both together. That is outside what a piston pump does, so it is not covered here.

How does a vacuum regulator work?

Equilibar's page on vacuum regulators (read 2026-11-20) describes the common mechanical type as a force balance. A diaphragm has atmospheric pressure on one side and the process vacuum on the other, and a spring provides the setpoint. The regulator sits between the process and the pump:

  • If the process goes deeper than the setpoint (absolute pressure too low), the diaphragm moves and restricts the flow to the pump, so the vacuum level falls back.
  • If the absolute pressure rises above the setpoint (vacuum too weak), the valve opens wider and the pump draws more, so the vacuum level rises again.

Equilibar points out that this kind of "vacuum regulator" is really a back pressure regulator, because it controls the pressure at its inlet port. It closes to raise the absolute pressure. Larger versions are often called vacuum control valves.

One detail matters in practice. Equilibar separates relieving regulators, which can let some gas into the process when you lower the vacuum setpoint, from non-relieving ones, which cannot. A non-relieving regulator on a perfectly tight system has no way to raise the pressure; Equilibar notes that most processes have at least a small in-leakage that solves this, and that a small controlled bleed at the regulator inlet can be added where they do not.

Leybold describes a close relative, the diaphragm controller, in which a rubber diaphragm closes or opens the end of a tube between the process and the pump against a reference pressure. Leybold says it has excellent control characteristics, that several can run in parallel for higher flow, and that it works between atmospheric pressure and about 10 mbar.

Vacuum regulator vs vacuum breaker

A vacuum breaker, also called a vacuum relief regulator, does the opposite job: it lets ambient air into the vacuum system. Equilibar classes it as a pressure reducing regulator, because it controls the pressure at its outlet port; it opens to raise the absolute pressure. Equilibar's comparison, in short:

  • Vacuum regulator: keeps the gas flow through the system low, which matters when several processes share a common vacuum supply, and, depending on the pump, may reduce electrical energy use. Depending on design and sizing, it can give very precise control. But it must be sized large enough to pass the entire vacuum flow, and pumps that need a minimum gas throughput may need a vacuum breaker as well.
  • Vacuum breaker: sometimes smaller, because less flow is needed to bring the vacuum down, typically cheaper, and useful for protecting some pumps from going beyond their design vacuum. But the extra gas flow wastes energy with some pump types, it can disturb other processes on a common header, and in most situations it does not control precisely over a wide flow window.

Is a vacuum regulator the same as a pressure regulator?

Not quite. A compressed-air pressure regulator lowers a high supply pressure to a set outlet pressure. A throttling vacuum regulator, as above, holds its inlet at a set vacuum, so it behaves like a back pressure regulator. The vacuum breaker is the one that works like a pressure reducing regulator. Equilibar also notes that an electronic vacuum regulator works like an electronic pressure regulator, except that ambient air feeds its inlet valve and the vacuum supply is connected to its outlet valve.

The bleed valve: the simplest method, and what it costs

VACUUBRAND's article on vacuum control types (read 2026-11-20) calls a hand-set valve a rough and indirect adjustment: you change the effective flow from the application to the pump, either by letting air in or by narrowing the passage, and get an approximate vacuum level, never an exact constant value. That can be enough, and VACUUBRAND gives filtration as an example. The drawbacks it lists for a false-air (bleed) valve are that oxygen from the air enters the system, and that bleeding disturbs other users on a multi-user lab vacuum system.

The less obvious cost is the pump. At a steady pressure, everything the pump removes has to come in somewhere. A pump that draws a volume flow S at an absolute inlet pressure p moves, in free air at atmospheric pressure, about S × p / patm. With a bleed holding the setpoint, everything the process does not use comes in through the bleed, and the pump runs at full effort all the time.

Worked example. Take an HC280D, whose parameter table lists 90 L/min (3.18 cfm), and a setpoint of 300 mbar absolute (about −71 kPa gauge, 21 inHg). The free air it can move at that pressure is at most 90 × 300 / 1013.25 = about 26.6 L/min (0.94 cfm). This is our calculation and an upper bound: a piston pump's real speed at 300 mbar is lower than its listed flow, so read the curve. If the process itself leaks in 0.5 L/min of free air, the bleed has to admit the rest, up to about 26 L/min of room air, continuously, for the pump to sit at 300 mbar. That air carries dust and moisture with it, so put a filter on the bleed inlet. The same reasoning is why the regulator in a milking system admits whatever the pump removes beyond what milking uses; see milking machine vacuum pump.

Two-point control: a vacuum controller and an on/off valve

A vacuum controller measures the pressure and switches. VACUUBRAND describes the common version: a solenoid valve between the application and the pump that opens fully when the pressure rises above the set value and closes when it is reached again, so the vacuum "fluctuates" between the two switching points within the hysteresis. Leybold describes the same thing as two-step regulation by pumping-speed throttling, and the mirror image, two-step regulation by gas admission, where a gas inlet valve opens at the lower switching point and closes at the upper one. Combining the two gives three-step regulation.

Many vacuum gauges and controllers make this easy. Leybold notes that electronic gauge units commonly provide a 0 to 10 V recorder output and built-in switching points ("trigger values"), and that a separate diaphragm pressure switch can switch a valve without displaying a value at all.

Worked example: how often will it switch? Suppose a 10 L vessel is held between 200 and 250 mbar absolute (about −81 and −76 kPa gauge), the process leaks in 0.5 L/min of free air, and the pump's curve gives about 40 L/min (1.4 cfm) of speed in that range. All of these are example inputs; use your own.

  • Valve open, pressure falling from 250 to 200 mbar: t = (V / S) × ln(p1 / p2) = (10 / 40) × ln(1.25) = 0.25 × 0.223 = 0.056 min, about 3.3 s. The formula is explained in our evacuation time guide.
  • Valve closed, pressure rising from 200 to 250 mbar: the leak raises the pressure by patm × q / V = 1013.25 × 0.5 / 10 = about 50.7 mbar per minute, so the 50 mbar band takes about 59 s.

So the valve opens roughly once a minute for a few seconds, about 57 times an hour. Add a 20 L buffer tank (30 L in total) and the same band takes about 10 s to pump down and about 2 min 58 s to leak up: about 19 cycles an hour. A narrower band holds the pressure tighter but switches more often. Our vacuum reservoir sizing guide covers buffer volume, and the leak rate guide covers how to measure the q in this sum.

If you switch the pump itself instead of a valve, the same numbers become motor starts. Check them against the pump's allowed start frequency; see vacuum pump duty cycle and start-stop frequency.

Speed control: run the pump only as fast as needed

The third way to change pumping speed is to change the pump's speed. VACUUBRAND describes this as adjusting the motor speed as required, which lets the pressure be set continuously and precisely, with the pump running only as fast as the process needs. In evaporation, its controllers also track the boiling pressure as it changes during the run, which a fixed two-point setting cannot do: VACUUBRAND notes that two-point control detects only the first boiling point and may let the process stall.

Speed control needs a pump and a drive designed for it. A DC pump is the natural candidate, but a rated voltage on a spec sheet does not by itself tell you over what speed range the pump will run, start and cool properly. If your design varies the pump's speed, specify how (supply voltage or a speed signal) and the range you need, and get the flow at your working pressure at both ends of that range.

Electronic regulators and PID control

Between the purely mechanical regulator and a speed-controlled pump sit electronic regulators:

  • SMC's vacuum regulator range (read 2026-11-20) includes hand-adjusted diaphragm regulators and electro-pneumatic units that control vacuum steplessly in proportion to an electric signal, with an integrated monitor output.
  • Equilibar describes electronic vacuum regulators with two fast servo valves and an internal pressure transmitter: one valve admits ambient air, the other connects to the vacuum supply. Equilibar also uses a small electronic regulator to set the dome of a larger mechanical one, so a computer can change the setpoint while the big valve handles the flow.
  • Kurt J. Lesker's pressure control overview (read 2026-11-20) names the capacitance manometer as the gauge of choice for control, with accuracy of typically 0.25% and response time of typically 100 ms, independent of gas type.

Leybold adds a warning about PID loops with proportional valves: because vessel volume, effective pumping speed and the control range differ so much from system to system, matching controller and valve is difficult, such loops tend to oscillate when the process is disturbed, and it is virtually impossible to give general standard settings. Its advice is that many control problems are better solved with a diaphragm controller. In practice: start with the simplest method that meets your tolerance.

Which method should you use?

If your situation is… Start with Why
One process, a rough level is fine (for example filtration) Bleed valve, or a vacuum breaker Cheapest; VACUUBRAND names filtration as a case where it may be enough. See vacuum filtration
The pump must not go beyond a vacuum limit Vacuum breaker / relief regulator Equilibar names pump protection as one of its uses
Several stations share one vacuum supply A throttling vacuum regulator at each station Bleeding at one station disturbs the others (Equilibar, VACUUBRAND)
Hold a level within a window, automatically Vacuum controller and solenoid valve Simple, and the window is set electronically; add buffer volume to slow the switching
Demand changes during the run (for example drying) Controller with a speed-controlled pump, or an electronic regulator Continuous control without a fixed bleed. See vacuum pump for a vacuum oven
Machine needs alarms, interlocks and restart rules Any of the above, plus defined control logic See vacuum pump control logic for states, permissives and sensor placement

What vacuum control means for choosing the pump

  1. Size the pump at the controlled pressure. A regulator or controller can only take vacuum away. The pump must reach the setpoint with margin while handling the process gas, the leaks and, with a bleed, the bleed air. Compare pumps on their curve at your working pressure, not on their deepest rating; our guide to ultimate pressure vs working vacuum explains why.
  2. Know how the control method loads the pump. With a bleed or a breaker the pump runs at full flow all the time. With a throttling regulator or a closed valve, it runs against a restricted or closed inlet for long periods. With two-point control of the pump itself, it starts and stops. Each of these is a different duty; tell the pump maker which one you plan.
  3. Put the sensor where the process is. The pressure that matters is in the vessel, not at the pump inlet; line losses between them are covered in our inlet piping guide.
  4. Filter what comes in. Bleed air and process gas both reach the pump. An oil-free pump has no oil for bleed air to contaminate, but dust and liquid still harm it.

HCEM oil-free piston vacuum pumps for controlled-vacuum equipment

We make oil-free piston vacuum pumps for equipment makers. The DC versions below are listed for 12, 24 or 48 V DC. The figures are from our parameter tables as listed: each model's table has a "flow" row and a "max vacuum" row. The last column is our calculation of the most free air each could move at a 300 mbar absolute setpoint (flow row × 300 / 1013.25), as in the bleed example above; the real figure is lower, so ask us for the curve. These pumps have not been tested by us with any particular regulator or controller.

Model Flow row Max vacuum row Power Noise Weight Free air at 300 mbar abs, at most (our calculation)
HC80D 28 L/min (0.99 cfm); −86 kPa 12 L/min; −95 kPa ≤70 W ≤48 dB(A) 1.5 kg 8.3 L/min
HC100D 50 L/min (1.77 cfm); −90 kPa 25 L/min; −98 kPa ≤150 W ≤56 dB(A) 2.45 kg 14.8 L/min
HC280D 90 L/min (3.18 cfm); −92 kPa 45 L/min; −98 kPa ≤180 W ≤58 dB(A) 4.9 kg 26.6 L/min
HC480D 100 L/min (3.53 cfm); −92 kPa 50 L/min; −98 kPa ≤200 W ≤58 dB(A) 7 kg 29.6 L/min
HC580D 120 L/min (4.24 cfm); −92 kPa 60 L/min; −98 kPa ≤260 W ≤62 dB(A) 7.3 kg 35.5 L/min
HC1100D 200 L/min (7.06 cfm); −92 kPa 100 L/min; −98 kPa ≤600 W not listed 12.6 kg 59.2 L/min
HC1500D 240 L/min (8.48 cfm); −92 kPa 130 L/min; −98 kPa ≤700 W not listed 12.6 kg 71.1 L/min

AC versions (220 V/50 Hz or 110 V/60 Hz) of most sizes are on our vacuum pump page. Our spec sheets give rated points, not speed ranges: if you plan to vary a DC pump's speed, tell us how and over what range, and we will confirm per model what we can supply. For how these pumps work, see how do vacuum pumps work.

Common questions

Can you regulate vacuum pressure?

Yes. Either reduce how much gas the pump removes (a throttling regulator, an on/off valve, or a slower pump) or let gas in (a bleed or a vacuum breaker). A controller with a sensor makes either automatic.

How does a vacuum regulator work?

The common mechanical type balances a spring against the difference between atmosphere and process vacuum across a diaphragm. When the vacuum gets deeper than the setpoint, it restricts the flow to the pump; when the vacuum weakens, it opens wider.

What is the difference between a vacuum regulator and a vacuum breaker?

A vacuum regulator throttles the line between the process and the pump. A vacuum breaker lets outside air into the system. The regulator keeps the gas flow low and suits shared vacuum supplies, but has to be sized for the whole vacuum flow; the breaker is often smaller and cheaper, but sends more gas through the pump and holds the setpoint less precisely.

Can I control vacuum by switching the pump on and off?

Yes, that is two-point control. Work out how often it will switch from the vessel volume, the band and the leak, as in the example above, and check that against the pump's allowed starts. A buffer tank reduces the number of starts.

Does controlling vacuum save energy?

It depends on the method. A bleed keeps the pump at full flow. Equilibar notes that a throttling regulator's lower gas flow may, depending on the pump, reduce energy use, and VACUUBRAND notes that a speed-controlled pump runs only as fast as needed.

Building vacuum control into your equipment, or choosing the pump for it? We supply oil-free piston vacuum pumps to equipment makers and distributors. Custom voltage and logo start at 50 units, and qualified OEM customers and distributors can apply for samples (subject to review), which take 10 to 20 days. See the OEM and ODM page, or send us your setpoint, your control method, the vessel volume and the gas load. Our engineers will tell you which pump fits and what flow data we have at your working pressure.

Sources

All read 2026-11-20 unless noted.

Back to blog