HCEM HC860A 10 bar oil-free air compressor pump

Bar vs PSI: How to Convert and Read Pressure Units on Compressor and Vacuum Pump Spec Sheets

HCEM Engineering Team

Bar and psi both measure pressure: force spread over an area. One bar is 100,000 pascals (100 kPa), close to the pressure of the atmosphere at sea level. One psi is one pound-force on one square inch. 1 bar = 14.504 psi, and 1 psi = 0.0689 bar (68.9 mbar), so a reading in psi is always about 14.5 times the same reading in bar.

The arithmetic is easy. The trouble on real spec sheets is everything around it: the same compressor rated at "7 bar", "700 kPa", "0.7 MPa" or "101.5 psi", a vacuum pump at "−92 kPa", and older gauges in kg/cm². This guide gives the exact factors, quick tables, shortcuts you can do in your head, the mistakes that most often cause trouble, and worked examples using the rating points of our own oil-free piston pumps.

What is bar pressure?

The bar is a metric unit of pressure defined from the SI unit, the pascal: 1 bar = 100,000 Pa = 100 kPa. It is not itself an SI unit, but it is exact, so converting between bar and kPa never loses accuracy. The name comes from the Greek baros, weight.

Three pictures help to feel the size of one bar:

  • The atmosphere. The standard atmosphere is 1.01325 bar, so 1 bar is about 1.3% less than normal air pressure at sea level.
  • Force on a fingertip. 1 bar pushes with 10 newtons on every square centimetre, about the weight of a 1 kg mass on a one-centimetre square.
  • Water depth. 1 bar is the pressure of about 10.2 metres of fresh water.

For smaller pressures the millibar is used: 1 mbar = 0.001 bar = 100 Pa, which is exactly one hectopascal (hPa), the unit of weather maps.

What is psi?

Psi stands for pounds per square inch, strictly pound-force per square inch (lbf/in²). One pound-force is 4.44822 N and one square inch is 6.4516 cm², so 1 psi = 4.44822 ÷ 0.00064516 = 6,894.76 Pa, or 6.895 kPa.

Because one psi is about one-fifteenth of a bar, psi figures are larger numbers for the same pressure: a pump rated at 8 bar is rated at 116 psi. Neither unit is more precise than the other. The precision is in the instrument and in how many digits the datasheet prints.

Bar vs psi: what is the difference and how do you convert?

The only difference is the size of the unit. Bar belongs to the metric system and psi to the imperial one, and both describe exactly the same physical quantity. The factors are:

  • bar to psi: multiply by 14.5038.
  • psi to bar: multiply by 0.0689476 (or divide by 14.5038).
  • psi to kPa: multiply by 6.89476.
  • kPa to psi: multiply by 0.145038.
  • bar to kPa: multiply by 100. MPa to bar: multiply by 10.

Bar to psi for the pressures you meet on compressor and pneumatic datasheets:

bar kPa MPa psi
0.5 50 0.05 7.25
1 100 0.1 14.50
2 200 0.2 29.01
3 300 0.3 43.51
4 400 0.4 58.02
5 500 0.5 72.52
6 600 0.6 87.02
7 700 0.7 101.53
8 800 0.8 116.03
10 1,000 1.0 145.04
12 1,200 1.2 174.05
16 1,600 1.6 232.06

And psi to bar, for specifications written in imperial units:

psi bar kPa
10 0.69 68.9
30 2.07 206.8
50 3.45 344.7
60 4.14 413.7
80 5.52 551.6
90 6.21 620.5
100 6.89 689.5
116 8.00 799.8
120 8.27 827.4
125 8.62 861.8
145 10.00 999.7
150 10.34 1,034.2
180 12.41 1,241.1

How can you convert bar and psi in your head?

Two shortcuts are accurate enough for a first check in a meeting or on a phone call:

  • bar to psi: multiply by 15, then take off 3%. 7 bar × 15 = 105, and 105 − 3% = 101.9 psi. The exact answer is 101.5 psi, so the shortcut is 0.3% high. Multiplying by 14.5 is closer still: 7 × 14.5 = 101.5.
  • psi to bar: multiply by 0.07, then take off 1.5%. 100 psi × 0.07 = 7.0, and 7.0 − 1.5% = 6.895 bar, which is the exact answer to four figures, because 0.07 × 0.985 = 0.06895.

For anything that goes into a drawing, a test report or a purchase order, use the exact factors and keep at least three significant figures.

Which pressure units appear on spec sheets, and how do they compare?

Bar and psi are the two you meet most, but a buyer comparing UK, German and Chinese documents will see the whole family below. All values are rounded to four or five significant figures.

Unit Symbol In bar In psi In kPa Where you usually meet it
bar bar 1 14.504 100 European compressor and pump datasheets
millibar mbar 0.001 0.014504 0.1 Vacuum, blowers, filters, low pressures
hectopascal hPa 0.001 0.014504 0.1 Weather data; identical to mbar
kilopascal kPa 0.01 0.14504 1 SI and Chinese factory datasheets
megapascal MPa 10 145.04 1,000 Chinese gauges, hydraulics, vessel ratings
pound-force per square inch psi 0.068948 1 6.8948 Air tools, North American and many UK datasheets
standard atmosphere atm 1.01325 14.696 101.325 Physics, reference conditions
kilogram-force per cm² kgf/cm² (often "kg/cm²") 0.98067 14.223 98.067 Older gauges and some Asian equipment
metre of water mH₂O 0.098067 1.4223 9.8067 Pumps, aeration depth
inch of water inH₂O 0.0024909 0.036127 0.24909 Fans, ventilation, filter pressure drop

The unit symbols are case-sensitive, and the case matters: kPa is kilo (lower-case k) pascal, MPa is mega (capital M) pascal, and mbar is milli (lower-case m) bar. "Kpa" or "KPA" is a common typing habit, ours included, and always means kPa. "Mbar", read strictly, would be a megabar, a million bar; on a vacuum datasheet it means mbar in practice. German documents write the decimal comma, so "0,7 MPa" is 0.7 MPa.

Which unit leads depends on the market. UK industrial datasheets usually lead with bar and print psi beside it, while air tools and imported North American equipment stay in psi. German datasheets work almost entirely in bar and mbar. Chinese factory documents often use kPa or MPa; our own spec tables, for example, read "60 L/min @ 700 kPa" where a UK catalogue would print "7 bar".

What mistakes do buyers make with bar and psi?

The conversion itself rarely goes wrong. These five slips are the usual causes of conversion errors in RFQs and comparisons:

  1. Using 14.7 instead of 14.5. 14.7 psi is one atmosphere, not one bar. 8 bar × 14.7 = 117.6 psi, against the correct 116.0 psi: 1.4% too high, enough to make two identical pumps look different.
  2. Reading kg/cm² as bar. 1 kgf/cm² is 0.981 bar. A gauge reading of 7 kg/cm² is 6.86 bar or 99.6 psi, not 7 bar or 101.5 psi: a 2% difference.
  3. Losing a factor of 10 or 1,000 in the metric prefixes. 700 kPa is 7 bar, not 70 bar, and 0.7 MPa is also 7 bar. Write every pressure in your comparison sheet in one unit before you look at it.
  4. Rounding before comparing. "100 psi" is often treated as 7 bar, which is 101.5 psi. That is close enough for a tool, but 120 psi is 8.27 bar, and a pump rated at 8 bar does not meet it.
  5. Mixing reference points. Every rating in this guide is gauge pressure, read from the surrounding atmosphere, which is how compressor datasheets and our vacuum tables state it; many European vacuum datasheets give absolute mbar instead. Whether a figure is gauge or absolute is a separate question from bar or psi: the same number in the same unit can mean either, so check for a suffix (g, a or abs) before comparing two sheets.

Why is a pressure in bar or psi never enough on its own?

A pressure tells you how hard the air pushes, not how much air arrives. An air pump's delivered flow falls as its outlet pressure rises, so a flow figure only means something at the pressure it was measured at, and a pressure only means something with the flow that goes with it. That is why our product tables write each rating as one point, for example "60 L/min @ 700 kPa".

The same pair, written two ways, is easy to compare once you convert both halves. Suppose one supplier quotes "3.5 CFM at 116 psi" and another "100 L/min @ 800 kPa":

  • 116 psi × 0.0689476 = 8.00 bar = 800 kPa: the same pressure.
  • 100 L/min × 0.0353 = 3.53 CFM: within 1% of the same flow.

The two ratings describe the same point, provided both flows are measured on the same basis. See what CFM, SCFM and free air delivery mean for that check, the CFM to L/min converter for the flow side, and PSI vs CFM explained for how pressure and flow trade against each other.

How do you read the pressure line on HCEM spec sheets?

Our product pages state each air pump's rating as a flow at a pressure in kPa, while some product titles use bar for the same figure. The table converts the rated points from the spec tables of six of our AC oil-free piston pumps; the flow in CFM is the L/min figure × 0.0353.

Model Spec table rating bar psi Flow in CFM Product title says
HC280 20 L/min @ 700 kPa (220 V/50 Hz); 25 L/min @ 700 kPa (110 V/60 Hz) 7 101.5 0.71; 0.88 "700Kpa"
HC580 60 L/min @ 700 kPa 7 101.5 2.12 "7 Bar"
HC1100 100 L/min @ 800 kPa 8 116.0 3.53 no pressure given
HC1500 120 L/min @ 800 kPa 8 116.0 4.24 "800Kpa"
HC860A 40 L/min @ 1000 kPa 10 145.0 1.41 "10bar"
HC1800A 90 L/min @ 1000 kPa 10 145.0 3.18 "10bar"

"7 Bar" in the HC580's title and "700 kPa" in its table are the same number, and so are "10bar" and "1000 kPa" for the HC860A and HC1800A. Each rating is one point on the pump's curve: for flow at other pressures, see the datasheet on each product page, and how to request and compare air pump performance curves for what to ask for. The full range is in our AC air compressor pumps.

How do you turn a psi specification into a pump choice?

A UK machine builder's specification says the pneumatic actuator needs 90 psi and an average of 1.5 CFM. The pump will sit in the machine base, with a filter, a regulator and a few metres of tubing between it and the actuator.

  1. Pressure at the actuator: 90 psi × 0.0689476 = 6.21 bar.
  2. Add the losses: assume 0.4 bar across the filter, tubing and valve at full flow, plus 0.3 bar so the regulator has something to regulate. Our pressure drop calculator estimates the pipe part.
  3. Pressure needed at the pump outlet: 6.21 + 0.4 + 0.3 = 6.91 bar = 691 kPa = 100.2 psi.
  4. Flow: 1.5 CFM × 28.3168 = 42.5 L/min.

The HC580's rating point is 60 L/min at 700 kPa: 42.5 ÷ 60 = 71% of its rated flow, but only 9 kPa (0.09 bar, 1.3 psi) above the outlet pressure needed. That is a thin pressure margin once the filter loads up. The HC1100's rating point is 100 L/min at 800 kPa: 1.09 bar of headroom, at the cost of a larger pump. Between the two, the deciding data is each pump's flow at 6.9 bar on its curve, which is what to ask us for, and the duty cycle the machine needs, covered in how to size an oil-free air pump.

Does a cylinder give the same force in bar and in psi?

Converting units never changes the physics, and a quick force calculation shows it. A pneumatic cylinder with a 32 mm bore works at 6 bar:

  • In metric: piston area = π ÷ 4 × 3.2² = 8.04 cm². Force = 6 bar × 10 N/cm² per bar × 8.04 cm² = 483 N.
  • In imperial: 32 mm = 1.260 in, so area = π ÷ 4 × 1.260² = 1.247 in². Pressure = 6 × 14.504 = 87.0 psi. Force = 87.0 × 1.247 = 108.5 lbf, and 108.5 × 4.448 = 483 N.

Both routes give the same theoretical force, before friction and the rod side are allowed for. Our pneumatic cylinder air consumption calculator turns the same bore and pressure into the air a cylinder uses.

How do bar and psi work for vacuum ratings?

Below atmospheric pressure the same units apply, with a minus sign on a gauge-referenced scale. Our oil-free vacuum pumps are rated in kPa with mmHg alongside. The HC580A vacuum pump, for example, lists a standard version with 120 L/min (4.24 CFM) free-air flow and an ultimate vacuum of −92 kPa (690 mmHg), and a high-vacuum version with 60 L/min (2.12 CFM) and an ultimate vacuum of −98 kPa (735 mmHg). In the other units:

Ultimate vacuum (spec table) bar mbar psi
−92 kPa −0.92 −920 −13.3
−98 kPa −0.98 −980 −14.2

The 690 and 735 mmHg in the table are the same two vacuum levels in a third unit (1 kPa = 7.5 mmHg), not extra performance. A gauge reading cannot fall further than the atmosphere pushing on it, about −1.013 bar or −14.7 psi at sea level, which is why vacuum ratings cluster just above that limit. How a pump reaches those levels is covered in how vacuum pumps work, and why the last few kPa matter less than flow at your working point in ultimate pressure vs working vacuum. Our oil-free vacuum pumps are rated the same way.

How should you write pressure in an RFQ?

  • One unit, stated: pick bar, kPa or psi and use it throughout; add the second unit in brackets if your team or ours works in the other.
  • The reference: gauge or absolute, written out, not left to the reader.
  • The place: at the pump outlet or inlet, or at the point of use after filters and valves.
  • The pair: the flow you need at that pressure, with its unit and basis.
  • The limits: maximum system pressure, the setting of any relief valve, and the lowest pressure your process tolerates.

Common questions

How many psi is 1 bar?

1 bar is 14.504 psi. For quick work, 14.5 is accurate to 0.03%.

Is 1 psi the same as 1 bar?

No. 1 bar is 14.5 psi; 1 psi is 0.069 bar.

How many bar is 100 psi?

100 psi is 6.89 bar, or 689.5 kPa. It is often rounded to 7 bar, which is actually 101.5 psi.

Is 1 bar the same as atmospheric pressure?

Close, but not exactly. The standard atmosphere is 1.01325 bar (14.696 psi), and real atmospheric pressure varies with weather and altitude.

What is 0.8 MPa in bar and psi?

0.8 MPa is 800 kPa, 8 bar or 116 psi.

Is a higher psi rating always better?

No. Pick a pump for the pressure your process needs plus losses and margin. Running at a higher pressure than you need costs flow, energy and wear.

If your specification mixes bar, psi and kPa, send us the pressure you need, where it is measured, the flow at that pressure and your supply voltage, and our engineers will convert it into a rating point and suggest a model from our oil-free range.

Back to blog