HCEM HC580D oil-free piston vacuum pump, DC version

Maple Sap Vacuum Pump: How Much Vacuum, How Many CFM per Tap, and Which Pump to Choose

HCEM Engineering Team

A maple sap vacuum pump should hold at least 15 inHg (about −51 kPa) at the far end of your lateral lines (UNH Extension); in a 2007 Vermont survey cited by UVM's Proctor Maple Research Center, vacuum users averaged about 21 inHg at the pump. Size it at roughly 1 to 1.5 CFM per 100 taps, counted at your working vacuum (Cornell NYS notebook). A free-air rating is about twice a pump's rating at 15 inHg, and capacity drops about 10% for every inch above 15.

This guide is for hobby and small commercial sugarmakers and for builders of sap-collection equipment. Every maple figure comes from the university and extension sources named in the text and listed at the end, all read on Nov. 6, 2026.

Why does vacuum increase maple sap yield?

Sap leaves a taphole when the pressure inside the tree exceeds the pressure in the tubing. Without vacuum, that difference comes only from the tree's freeze-thaw pressure. Vacuum lowers the pressure at the spout, so sap flows faster in a good run and keeps flowing when conditions are marginal. The University of Vermont's manual Maple: A Sap to Syrup Guide (UVM Extension) recommends a pump that can run 24 hours a day, 7 days a week through the season.

  • Measured at the University of Vermont Proctor Maple Research Center. Wilmot, Perkins and van den Berg (Maple Syrup Digest, October 2007) held trees at 0 to 25 inHg. The best tree, at 25 inHg, gave 32.9 gallons from its taphole; the poorest, a gravity tree, gave 5.0, with a strong link between vacuum and yield. Higher vacuum did not dilute the sugar, shift pH or minerals, or significantly change internal wood staining.
  • About 5% more sap per inch. Ohio State University Extension (Les Ober, 2019 and 2020) gives 5% to 7% per inch of vacuum, as does the UVM manual. At 15 inHg that roughly doubles the gravity yield.
  • Steady gains per inch. Ohio State's summary of the Proctor data: 0 to 15 inHg added about 8 gallons of sap per tap, 15 to 20 inHg about 3 more, and 20 to 25 inHg about 2.5 more, roughly half a gallon per inch all the way up, while pump capacity falls about 10% per inch.
  • Season totals. Cornell's New York State Maple Tubing and Vacuum System Notebook (6th ed., Stephen Childs) reports 50% to over 200% more sap; UNH Extension's maple setup guide gives 50% to 100%.

The Proctor paper also cites a 2007 Vermont survey: producers above 20 inHg at the pump averaged 0.30 gallons of syrup per tap, those at 1 to 19 inHg 0.22, and tubing without a pump 0.17. That is a survey pattern, not proof that vacuum alone made the difference.

What vacuum level should a maple system run at?

Maple gauges read inches of mercury below atmospheric pressure; pump datasheets often use kPa gauge or absolute. Against a standard sea-level atmosphere of 101.3 kPa (29.92 inHg):

Gauge (inHg) Gauge (kPa) Absolute at sea level (kPa) Meaning in a sugarbush
15 −50.8 50.5 UNH Extension's minimum at the end of the laterals; the level maple pumps are usually rated at
18 −61.0 40.3 Top of the 12 to 18 inHg range Cornell's beginner notebook says most vacuum pumps perform well in
20 −67.7 33.6 About the 20.7 inHg survey average at the pump
25 −84.7 16.6 Highest level in the Proctor trial
27.2 −92 9.3 Rated vacuum of HCEM's standard oil-free piston builds (tables below)
28 −94.8 6.5 About the maximum at 2,000 ft elevation (Proctor paper)
  • The reading that counts is at the last tap. Ohio State notes that a gauge at the pump can read 28 inHg while the woods see 18 inHg or less, because an undersized mainline cannot carry air to the pump fast enough (line loss). It suggests working at about 20 to 27 inHg, depending on the system.
  • Elevation caps the gauge. The Proctor paper gives about 30 inHg at sea level and 28 inHg at 2,000 ft; Ohio State's rule is about 1 inch less per 1,000 ft. See our guides to gauge and absolute pressure and to altitude and ambient conditions.
  • Higher vacuum costs capacity. Research summarized in the NYS notebook found pump capacity fell 9% to 23% per inch of added vacuum. One pump rated 60 CFM at 15 inHg still moved about 60 CFM at 18 inHg but only 20 CFM at 24 inHg. The step from 20 to 25 inHg buys the least sap and costs the most pump.

How many CFM per tap does a maple vacuum pump need?

Air enters the tubing as gas from every taphole and through leaks at fittings, spouts, cracks and squirrel chews. The vacuum settles where the pump's capacity balances that inflow. The sources agree on these rules of thumb:

  • 1 to 1.5 CFM per 100 taps (UNH Extension; NYS notebook, which says to use the higher figure for long mainlines). Ohio State uses 1 CFM per 100 taps as the baseline load.
  • Count CFM at the working vacuum. Maple pumps are usually rated at 15 inHg; a free-air rating, common for pumps from other trades, is usually about twice as high (NYS notebook).
  • Deduct 10% of the 15-inch rating per inch above 15 when no performance curve is available (NYS notebook; Ohio State).
  • Releasers and lifts use air too. Ohio State budgets at least 5 CFM for a mechanical (manual) releaser, plus 3 to 5 CFM in reserve.

Worked example: 150 taps, 20 inHg at the pump.

  1. Load at 20 inHg: 150 × 1 ÷ 100 = 1.5 CFM for a tight system with short mainlines; 150 × 1.5 ÷ 100 = 2.25 CFM with long or older lines.
  2. To a 15-inch rating: 5 inches × 10% = 50% lost, so 1.5 ÷ 0.5 = 3.0 CFM at 15 inHg (or 4.5 CFM).
  3. To free air: about twice that, roughly 6 CFM free air (or about 9 CFM).
  4. Releaser: Ohio State's 5 CFM for a mechanical releaser would raise this load more than fourfold, to 6.5 CFM, so on a small system ask how much air the releaser uses. The NYS notebook also lists electric releasers and vacuum-rated holding tanks.

Leaks change the answer fast. Leaks letting in another 1 CFM at 20 inHg raise the load to 2.5 CFM, which means 5 CFM at 15 inHg and about 10 CFM free air. Mainline size limits what any pump can deliver: in an Ohio State example, a 1-inch, 1,000-ft mainline passed about 7 CFM on a 15 CFM pump and only 8 CFM on a 60 CFM pump. Use our CFM to L/min converter for pumps rated in L/min.

The notebook warns that each pump type loses capacity differently as vacuum rises, so treat these rules as a starting point and confirm with the maker's flow at your working vacuum. Our article on ultimate pressure versus working vacuum explains why a pump should not run near its ultimate, and vacuum pump evacuation time covers pump-down after a stop.

Which types of vacuum pump do sugarmakers use?

Type Vacuum in maple use Strengths Watch out for
Liquid ring Close to 29 inHg Highest vacuum; one of the most popular maple pumps Needs water, oil or water with antifreeze; water must stay above freezing
Oil-lubricated rotary vane (newer, flood) 27 to 29 inHg Continuous duty; oil pumps cope better with cold pump houses Constant oil supply; oil recovery; overheating if held too high too long
Old dairy rotary vane About 15 to 16 inHg Cheap or even free Overheats if pushed higher
Rotary claw 27 to 28 inHg Continuous duty, little in-season maintenance Expensive; off-season oil fogging; dry pumps are more moisture-sensitive
Piston Depends on design Listed as a maple pump type by the NYS notebook and UVM manual The notebook's piston pumps run on oil; oil-free ones are dry and need a reliable moisture trap
Diaphragm sap (liquid) pump Only while sap flows Low cost; good for small operations Moves little air; vacuum fades when flow stops; ice damages diaphragms
3/16-inch tubing, no pump Natural vacuum from the drop No power Best with 15 ft or more of fall and a 6% to 10% slope; leaks erase the gain

Sources: Ohio State's "Quest for High Vacuum" posts (2016) and 2019 update, the NYS notebook and the UVM manual. A diaphragm sap pump moves liquid; a diaphragm vacuum pump moves air, as our diaphragm vs piston pump comparison explains.

The releaser (or extractor) is not the vacuum pump. It passes sap from the mainline to the tank without breaking the vacuum, using vacuum and gravity (mechanical) or a sensor and sap pump (electric). Ohio State estimates 0.2 gallons or more of sap per tap per hour at peak flow, so 150 taps can deliver 30 gallons an hour or more to the releaser.

How do you keep sap and moisture out of the pump?

The NYS notebook, the UVM manual and Ohio State all warn that sap or water getting into the pump can wreck it. From the woods to the pump, the NYS notebook and UVM manual describe:

  1. Releaser, which takes the sap out of the air stream.
  2. Moisture trap, the backstop that stops sap reaching the pump when a releaser sticks or floods.
  3. Check valve, which limits surges that can push contaminated sap back into tapholes when the pump stops. An undersized one costs capacity.
  4. Pressure control valve, a regulated air bleed beside the pump that sets the working vacuum.
  5. Gauges at the pump, the releaser and the mainlines.

For an oil-free (dry) pump, the moisture trap is essential: the UVM manual notes that dry and claw pumps are more susceptible to moisture damage. Plan a trap you can drain and check daily. The NYS notebook also warns against siting the pump where its exhaust can reach a bubbler or air-injection intake, which risks off-flavored syrup.

AC or 12/24 V DC: how do you power an off-grid sugarbush pump?

Cornell's beginner notebook (Chapter 2) names access to power and price as the two main issues for small producers. Its examples range from a gas-engine pump on a trailer, to 110 V pumps for a few up to about 500 taps, to very small 12 V pumps for the smallest systems (the caption says “1 to 30 pumps”, evidently taps). With grid power, a 110 V/60 Hz AC pump is simplest. Off-grid, a DC pump runs from batteries charged by solar, but a pump meant to run around the clock needs a real energy budget.

Worked example: daily energy for a DC pump. A pump whose table gives ≤180 W, such as the 12 V HC280C, uses up to 180 W × 24 h = 4.32 kWh a day: 180 ÷ 12 = 15 A, or 360 Ah a day at 12 V. If a weather controller (the NYS notebook describes these) runs it 10 hours a day, that falls to 1.8 kWh, or 150 Ah. Size batteries and panels on the table maximum, then divide the daily energy by your site's March peak sun hours and add margin for snow and battery losses. Our article on AC vs DC oil-free pumps covers the electrical side.

How do you find leaks in a maple vacuum system?

The UVM manual gives three methods. Watch the sap where a lateral loops up into the mainline: sap that flutters or rushes with lots of bubbles means a leak further up. Listen for the whistle of a fallen spout or the soft hiss of a small leak. And use gauges: close the mainline valves one at a time and watch the releaser gauge, or use a remote monitoring system. Cornell's beginner notebook turns readings into a diagnosis:

Pump vs top of the mainline Diagnosis
Within 2 inHg, top above 15 inHg Well designed, highest productivity
2 to 4 inHg apart, or top below 15 inHg Tubing undersized or slope problems
More than 4 inHg apart, or top below 10 inHg Poor design
No vacuum at the top Unacceptable

To check the pump itself, see how to test a vacuum pump. To measure how much air an isolated section lets in, see our vacuum leak rate guide.

What about cold weather?

  • Liquid ring pumps need water kept above freezing, or antifreeze that then has to be recovered (Ohio State; NYS notebook).
  • Oil-based pumps cope better with pump houses below freezing (NYS notebook).
  • Diaphragm sap pumps must be protected from freezing and from ice in the lines (Ohio State).
  • Rotary claw pumps can rust during long layovers and need oil fogging off-season (Ohio State).

Check every pump's ambient range. The tables of our AC models (HC580A, HC680A, HC1500A) list −5 to 40 °C (23 to 104 °F), and the DC tables give no range. A colder pump house needs heat or insulation. Tell us your conditions and we will confirm what applies.

Where does an oil-free piston vacuum pump fit?

An oil-free piston pump has no oil to top up, no oil mist and no oil recovery. Its standard versions are rated to −92 kPa (about 27 inHg), above the 20.7 inHg average at the pump in the 2007 Vermont survey, and its free-air flow suits small tap counts under the rules above. The limits: it is a dry pump that depends on a working releaser and moisture trap, its flow is far below the large pumps that serve thousands of taps, and none of the maple sources tested one.

Our oil-free vacuum pumps list their parameter tables on each page. From the live pages (shopify pull 2026-10-31/141109282708), "Max. Open Air Flow" row, standard versions rated to −92 kPa:

Model Supply Free-air flow Max. power Weight
HC580A / HC580B 220 V 50 Hz / 110 V 60 Hz 120 L/min (4.24 CFM) ≤340 W 10.1 kg
HC680A / HC680B 220 V 50 Hz / 110 V 60 Hz 165 / 170 L/min (5.83 / 6.01 CFM) ≤340 W 9.9 kg
HC1500A / HC1500B 220 V 50 Hz / 110 V 60 Hz 210 / 250 L/min (7.42 / 8.83 CFM) ≤700 / ≤750 W 17.5 kg
HC580C / D / E 12 / 24 / 48 V DC 120 L/min (4.24 CFM) ≤260 W 7.3 kg
HC280C / D / E 12 / 24 / 48 V DC 90 L/min (3.18 CFM) ≤180 W 4.9 kg

Each page also lists a high-vacuum version (−98 kPa at about half the flow). The standard version gives about twice the flow, and flow is what keeps up with leaks; the −98 kPa version's extra depth helps only a very tight system.

On paper, the 150-tap example (about 6 CFM free air) falls at the HC680B's 6.01 CFM, the long-line case (about 9 CFM) just above the HC1500B's 8.83 CFM, and a 40-tap line (0.4 CFM at 20 inHg, 0.8 at 15 inHg, about 1.6 free air) within the 12 V HC280C's 3.18 CFM. These figures leave no reserve and no air for a releaser. A mechanical releaser (at least 5 CFM in Ohio State's budget) or Ohio State's 3 to 5 CFM reserve would exceed every model in the table, so they suit only small systems without a mechanical releaser, and even the long-line case is just beyond the HC1500B. These are rule-of-thumb estimates, not ratings: the rules come from other pump types, and we have not tested our pumps on maple tubing or rated them for outdoor, below-freezing or wet-air use. Tell us your tap count, tubing, mainline lengths, elevation, power and pump-house conditions, and we will confirm whether a model fits, or say plainly that it does not.

Equipment makers building vacuum packages or off-grid sap units: add the tap range per unit, releaser type, enclosure temperatures, supply voltage and annual volume. Standard models have no fixed minimum order; custom voltage and logos start at 50 units; qualified OEM customers and distributors can apply for samples (10 to 20 days). See our OEM and ODM page.

Common questions

How much vacuum do you need for maple sap?

At least 15 inHg at the end of the laterals (UNH Extension). Vermont vacuum users averaged about 21 inHg at the pump in 2007, and Ohio State suggests 20 to 27 inHg. Each inch above 15 inHg adds about the same sap but costs about 10% of the pump's rated capacity, so high vacuum is mainly a question of pump size and leaks.

How many taps can a 5 CFM vacuum pump run?

If the 5 CFM is rated at 15 inHg, about 330 to 500 taps at 1 to 1.5 CFM per 100. If it is free air, it is about 2.5 CFM at 15 inHg, or 170 to 250 taps. At 20 inHg, halve those figures; leaks and long mainlines cut them further.

Do I need a moisture trap if I have a releaser?

Yes. It protects the pump when the releaser fails, and a dry oil-free pump depends on it.

Choosing a pump for a small sugarbush or designing sap equipment? Send us your tap count, tubing, target vacuum, elevation, power source and pump-house temperatures. Our engineers will suggest a model, or tell you honestly if an oil-free piston pump is not the right fit.

Sources

  • Wilmot, Perkins and van den Berg, UVM Proctor Maple Research Center, "Vacuum Sap Collection: How High or Low Should You Go?", Maple Syrup Digest, Oct. 2007: mapleresearch.org, read Nov. 6, 2026.
  • Cornell Maple Program (S. Childs), New York State Maple Tubing and Vacuum System Notebook, 6th ed.: mapleresearch.org, read Nov. 6, 2026.
  • Cornell Maple Program, Beginner's Notebook, Chapter 2, Sap Collection Systems: blogs.cornell.edu, read Nov. 6, 2026.
  • UNH Extension, "Maple Setup and Guidelines": extension.unh.edu, read Nov. 6, 2026.
  • L. Wolfe, Shelburne Farms and UVM Extension, Maple: A Sap to Syrup Guide: uvm.edu, read Nov. 6, 2026.
  • L. Ober, Ohio State University Extension, "The Quest for High Vacuum in a Maple Tubing System (Part 1)", 2016: u.osu.edu, read Nov. 6, 2026.
  • L. Ober, Ohio State University Extension, "The Quest for High Vacuum Part 2", 2016: u.osu.edu, read Nov. 6, 2026.
  • L. Ober, Ohio State University Extension, "Vacuum Tubing Systems, An Update", 2019: u.osu.edu, read Nov. 6, 2026.
  • L. Ober, Ohio State University Extension, "Optimizing the Performance of My Vacuum Tubing System: Part I", 2020: u.osu.edu, read Nov. 6, 2026.
  • L. Ober, Ohio State University Extension, "Tubing or Pump: How to Optimize your Tubing System's Performance", 2013: u.osu.edu, read Nov. 6, 2026.
Back to blog